Home » Linksys Routers » linksys wireless router wrt110 setup part 1

Category : Linksys Routers
Do not lose your chance to get this rare opportunity!
* Discount only for limited time, Buy it now!

"This Best Selling linksys wireless router wrt110 setup part 1 Tends to SELL OUT VERY FAST! If this is a MUST HAVE product, be sure to Order Now to avoid disappointment!"

linksys wireless router wrt110 setup part 1

This video shows how to set up a Linksys wireless router. I’m using a model wrt110, but all Linksys routers are amazingly similar. Even if you don’t have a L…

Question by jimbo 82: How do I setup security on my Linksys router without the cd?
How can I setup my Linksys router to where no one can steal my internet? I have no cd, and I tried typing admin and password (in multiple ways) already, and it never logs me into the router? Please jhlp…

Best answer:

Answer by AR
You can access router through its IP, which you can find it in Command Prompt after writing “ipconfig” it will like this “” etc.

Reset your router for change admin id/password.

Tip for Reset router, there is small whole on the back of router, insert pin/pen nib etc and hold for 20 sec approximately until the whole lights going off of the router, after that go to the local IP and start setup for configuration.

What do you think? Answer below!

Using a Linksys Wi-Fi router? It could be ripe for remote takeover
Some versions of a popular Wi-Fi router sold under the Linksys brand expose users to a variety of exploits that allow remote attackers to take full control of the devices, a security expert said. The most severe of the vulnerabilities in the "classic …
Read more on Ars Technica

FON Linksys Router
linksys routers
Image by illustir

Related Linksys Routers Articles

Wooww, nice product! I want to share this product!

What customers say about linksys wireless router wrt110 setup part 1?

  1. The login to most Linksys routers (usually IP address, is a blank username and “admin” (without the “‘s) as the password. Here are some security steps I recommend.

    Because routers differ as to details, I can’t be specific about how to accomplish these actions, but they’re almost all done from within the router’s administration web pages. Note: It’s best to do them from a computer cabled (even just temporarily) to the router rather than wirelessly, especially since wireless administration will be deactivated by action #1.

    Generally, to access your router’s administration pages, hook up a computer directly to the router and enter the router’s local IP address into a browser’s address window. See way below for details on finding your router’s IP address.

    1.Deactivate wireless access to your router’s administration web pages so only a computer connected via an Ethernet cable can reach them. This won’t affect wireless use of the Internet, just wireless administration of the router. Even if you don’t want to leave a computer connected via a cable, leave the cable there for when you need it.

    2.Turn off the SSID (network name) broadcast from the router. There’s no need to advertise your network’s presence. You’re not running a hotspot; everyone who should be on your network should know its name.

    3.Change your SSID from the default. Hackers know that routers come with default SSIDs and look for them. Even if the SSID isn’t being broadcast, if a hacker knows its name, they can hop on board.

    4.Set up encryption with an encryption key. The longer, the better. WPA (if your network and all your computers can support 802.11G) is better than WEP. WEP is better than nothing. Each of your wireless computers and devices will need this encryption key. Wired computers will not.

    5.(Optional) Limit access to only the computers you want on the network via MAC filtering. (MAC refers to unique NIC (Network Interface Card) addresses, not Macintosh computers, and not IP addresses.) This isn’t a defense against hardcore freeloaders — it’s possible to fake MAC addresses — but it keeps out casual interlopers.

    6.(Optional and only partially effective) Change the range of and/or limit the number of automatically assigned IP addresses (DHCP) to reduce the chance of extra users. Again, hackers know what ranges routers come from the factory with. Changing them makes it a little harder to hop on board.

    Here’s how to find your router’s IP address:

    1.Click on the Start->Run button.
    2.In the text box, type


    and press Enter.

    3.A black “DOS box” will pop up. In it, enter

    ipconfig /all

    A bunch of gibberish will fill the box. Next to “Default Gateway” an IP address will appear. This is your router’s IP address.

    That should go far toward hardening your wireless network.

  2. I had this problem earlier. Have you tried going into their website support section, this will probably help you setting up a password for your router.

AT&T 3G Microcell Wireless Cellular Signal Booster Tower Antenna by Cisco

Check Special Price!
AT&T 3G Microcell Wireless Cellular Signal Booster Tower Antenna by Cisco...

99-03 Volkswagen Golf, Jetta & GTI Cell Phone Car Mounting Bracket by Panavise

Check Special Price!
99-03 Volkswagen Golf, Jetta & GTI Cell Phone Car Mounting Bracket...

Epson Stylus Photo R2000 Wireless Wide-Format Color Inkjet Printer (C11CB35201)

Check Special Price!
Epson Stylus Photo R2000 Wireless Wide-Format Color Inkjet Printer (C11CB35201) Take...

HEWLETT-PACKARD Laserjet Pro M1536dnf Multifunction Laser Printer Copy/Fax/Print/Scan

Check Special Price!
HEWLETT-PACKARD Laserjet Pro M1536dnf Multifunction Laser Printer Copy/Fax/Print/Scan FastRes 1200 enhancement...

For all your Wireless Needs at the Lowest Price
Low Cost Wi-Fi is a participant in the Amazon Services LLC Associates Program,
an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com